Verilink PRISM 3000 (34-00184) Product Manual Manual de usuario descargar pdf (Pagina 43)

Terminal Operation 4-15PRISM 3000

4.7 Utilities Screen

The ‘Utilities’ screen (Screen 4-12) handles the functions

described in the following paragraphs.

4.7.1 General Functions

Set Time: The current time may be entered in this field

using the 24-hour HH:MM:SS format. For example, 3:45

AM is entered as ‘0345’ and 3:45 PM is entered as ‘1545’.

Set Date: The current date may be entered in this field

using the MM:DD:YY format. For example, July 4, 1993 is

entered as ‘070493’.

NOTE: The time and date can be set at the far end, but

not displayed.

New Password: This field allows entry of a password of up

to 10 characters. An empty string (carriage return only) may

be entered to disable the password feature. After <return> is

pressed, the new password is activated and is no longer visi-

ble. Therefore, type carefully when entering a new password

and verify before pressing <return>. When the terminal

interface is exited and later reactivated, this password must

be entered exactly to gain access. If the wrong password is

entered, the following message will appear:

Incorrect Password; Please Enter Again.

NOTE: Do not exit the terminal interface program until

the password procedure is fully understood. If a pass-

word has been specified, it must be typed exactly to

reenter the program.

If the user programs a password and later forgets it, the

password may be cleared through the front panel mainte-

nance reset (refer to Section 3.1.1 on page 3-1). The reset

operation sets all parameters to the factory default settings

and zeros all performance registers. If the reset operation is

not a satisfactory option, then call TxPORT Customer Sup-

port for a one time use ‘back door’ password (refer to Sec-

tion 1.7 on page 1-6 for telephone numbers).

Maintenance Reset: This field will clear all user selectable

parameters, performance registers, passwords, and alarms.

All alarm threshold parameters will be reset to default val-

ues. The unit reloads start-up configuration settings from the

default parameters stored in ROM. Pressing <return> on this

field brings up a warning prompt asking whether or not to

perform the reset function.

4.7.2 COA Parameters

The following fields pertain only to call on alarm functions.

Alarm Notification: This field controls the remote alarm

reporting. The choices are:

[OFF

] - Disables alarm reporting.

[DIRECT] - Sends reports to a printer or terminal con-

nected directly to the supervisory port.

[DIAL] - Sends reports through an attached ‘AT’ com-

mand set compatible modem connected to the ‘SUPV’

serial port, which must dial out to a remote modem. The

message format is described in the ‘Element ID’ field.

[DIAL NMS] - Sends reports through a modem to an

EM8000 element manager workstation.

Primary Phone#, Secondary Phone#: These fields are

ASCII strings for the primary and secondary call on alarm

phone numbers used in the [DIAL] and [DIAL NMS] modes.

The strings must NOT include the ‘ATDT’ command prefix.

3000

DSU x.xx/x.xx PRISM

3000

Date: MM/DD/YY

No Far End Response Miami: (97) Time: HH:MM:SS

---------------------------------- UTILITIES -----------------------------------

Element: [NEAR]

Set Time: (12:34:25)

Set Date: (04/30/93)

Alarm Notification: [DIAL ]

Primary Phone#: (205-555-1212 )

Secondary Phone#: (205-532-8853 )

Element ID: (DSU 1230 )

New Password: (JohnDoe )

(MAINTENANCE RESET)

Screen 4-12 Utilities

1 2 ... 38 39 40 41 42 43 44 45

Comentarios a estos manuales

Sin comentarios

Verilink PRISM 3000 (34-00184) Product Manual Manual de usuario Pagina 43

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware De La Computadora Verilink PRISM 3000 (34-00184) Product Manual