Verilink NetPath 2000 Product Manual Manual de usuario

iNetPathTM2000Reference ManualSeptember 200534-00343.A

x NetPath 2000

About NetPath 2000 1-1C HAPTER1CHAPTER 1ABOUT NETPATH 2000IntroductionThe NetPath 2000 enables a branch office to maintain network connectivity in cas

1-2 NetPath 2000Figure 1.1Typical Customer Network Configuration.The simplest fail-over configuration uses a static secondary default or subnet route

About NetPath 2000 1-3assignment to the branch office’s local network over its branch office router Ethernet interface.Figure 1.2NetPath 2000’s Method

1-4 NetPath 2000The front panel’s power switch LED is illuminated with the unit is on.Rear PanelThe NetPath 2000 rear panel is shown in Figure 1.4.Fig

Installation 2-1C HAPTER2CHAPTER 2INSTALLATIONThis chapter describes the contents of your NetPath shipment and provides information on connecting and

2-2 NetPath 2000Figure 2.1Shipment ContentsContact Verilink Technical Support (page vi) for assistance. Additional RequirementsThe NetPath 2000 has be

Installation 2-3255.255.255.0, and comes DHCP enabled. Either enable DHCP under your PC’s network settings, or configure your PC to an appropriate IP

2-4 NetPath 2000

Configuration 3-1C HAPTER3CHAPTER 3CONFIGURATIONThe NetPath 2000’s GUI is accessible from all three physical interfaces: the local management Ethernet

ii NetPath 2000FCC Requirements Verilink products have been assembled from tested components found to comply with the limitsfor a Class A digital dev

3-2 NetPath 2000NOTICE: You may need to disable personal firewalls or security programs to access this screen.The NetPath 2000 permits two levels of

Configuration 3-3Link-RecoveryDisplays the number of times the PCMCIA card has lost connection and the NetPath 2000 has had to reestablish connection

3-4 NetPath 2000After you enter the password, a screen similar to that shown in Figure 3.3 will appear.The configuration information contained in this

Configuration 3-5Figure 3.4Modify Configuration Screen

3-6 NetPath 2000Wireless Network InterfaceThe wireless network interface settings are described below.Keep AliveSelect OFF or ON for packet transmissi

Configuration 3-7Subnet MaskSets the address mask that delineates local subnet range. In most cases, the factory-default range of 255.255.255.0 will s

3-8 NetPath 2000New Shared Secret(PSK)Sets the shared secret password for authentication. This password is case sensitive.ConfirmConfirms the previous

Configuration 3-9Figure 3.5Code Update ScreenType the file location or select the “Browse” button to find the location of the file that contains the c

3-10 NetPath 2000Select the “Proceed” button to reset the NetPath 2000 unit. The unit will reboot. Select the “Cancel” button to abort the reset and r

Specifications A-1A PPENDIXAAPP ENDIX ASPECIFICATIONSRouting• Routes IP packets between wireless network card and branch router Ethernet interface.• D

iii3. Transfer. You may not rent, lease, lend or sublicense the Software. You may, however, make aone-time permanent transfer of all of your license r

A-2 NetPath 2000Hardware Interfaces• Local management Ethernet interface − management interface: RJ-45• Branch router Ethernet interface − branch rout

iv NetPath 2000“Commercial Computer Software Documentation”, as such terms are used in 48 C.F.R. §12.212or 48 C.F.R. §227.7202, as applicable. Consist

vTable of ContentsPrefaceAbout this Manual ...

vi NetPath 2000Applying Configuration Changes ... 3-8Cod

Preface viiCHAPTER 0PREFACEAbout this ManualThis reference guide for the NetPath 2000 describes unit features and specifications, configuration, and i

viii NetPath 2000Customer Service and Technical SupportVerilink provides easy access to customer support through a variety of services. This section d

Preface ixA product sent directly to Verilink for repair must first be assigned an RMA number. You may obtain an RMA number by calling Customer Servic