Verilink 1559 (CG) Configuration/Installation Guide Manual de usuario descargar pdf (Pagina 1)

Page 1

TRANSPORT

These procedures describe how to upgrade the TxPORT

1559 APS Manager from version 1.15 to version 3.XX. The

test center and central office technicians must understand

fully each procedure before attempting to perform the

upgrade.

Failure to complete every step in

each procedure may cause you to

lose key information in the unit database.

Pre-installation Checks

The central office technician should visually verify that the

1559 and associated 1557 cards have no alarm LEDs illumi-

nated. If any abnormal conditions exist, they should be

noted and discussed with the controlling test center before

proceeding. The test center responsible for this central office

should use the following prodecure to verify that the 1559 is

operating properly and obtain a hard copy of key database

information contained in the unit.

1. Access the 1559 APS Manager from the test center.

This step verifies that the dial line to the central office

is operating properly and that the 1559 is operating

properly.

2. Verify that the 1559 can access the dial-out COA line

by installing a spare 1557 card in a vacant slot and con-

figuring it for In-Service and setting a valid COA value

(1-12). When the card is configured for In-Service, the

1559 detects that the card is in alarm and reports the

alarm condition to the designated COA telephone num-

ber at the test center.

3. Access the Circuit List display and print a hard copy of

all equipped APS circuits installed in the office. If neces-

sary, use the arrow keys to view or print circuits not

being presently displayed. This information will be used

later to verify that no circuit ID data has been changed.

4. Access the Utilities/Password screen and print a hard

copy of this information to be used later when reenter-

ing the user names, setting temporary (“dummy”) user

passwords, and setting the user levels and password

expiration periods.

After installing the 3.XX software, these names

must be individually reentered along with a dummy

password and a valid user level. Don’t forget to

notify the APS users to change the dummy pass-

word to a valid password as soon as possible.

5. Access the Utilities/Call-On-Alarm screen and print a

hard copy of the COA information to be used later

when reentering the COA telephone number(s).

The COA number(s) must be reentered after the

3.XX software is installed. Also, the new bus

communications COA numbers (S1, and S2)

must be defined if the 1559 APS Manager is

required to report bus communications failures

to a designated repair location.

Required Equipment

The central office technician should verify that the follow-

ing tools and equipment are available to complete the

upgrade procedures without delays.

• Phillips-head screwdriver

• Hand test set for verification of dial-in/out telephone lines

• EPROM removal tool

• PC with terminal emulation capabilities

• DB-9 female to DB-25 male data cable

• TxPORT upgrade kit containing:

- Two EPROMs labeled Revision 2.0X and 3.XX

- A 3.5” diskette labeled Download 2.03 or higher

Installing the 2.0X EPROM

Upgrading the EPROM from revision 1.15 to 2.0X allows

you to download a database file using the TxPORT Download

software. This file contains the APS circuit IDs, Service State,

and the APS Manager name. This procedure does not impact

customer service (1557 APS cards continue to operate nor-

mally), however, the software should not be installed unless

the test center is online and all pre-installation checks are

complete.

1. Disconnect power from the 1559 by removing the front

panel GMT fuse. The unit’s green POWER LED indi-

cator turns Off.

2. Remove the 1559 front panel by removing the two Phil-

lips-head screws.

3. Locate the two EPROM sockets on the front edge of the

circuit board. The left socket (U31) is empty. The right

socket (U32) contains an EPROM labeled Revision 1.15.

4. Locate the strap option posts (JM12) left of U32. The

strap covers the left and center posts (512K

position).

Move the plastic post strap to cover the center and right

posts (1M position).

5. Using an EPROM removal tool, remove the 1.15

EPROM from the right socket (U32).

Note the key (indentation) on the

left side of the EPROM and install

the new EPROM in the same orientation.

Failure to do so may destroy the EPROM.

1559 APS Manager

Download Procedures

45-00111

1.0

1 2 3 4

Indice de contenidos

Pagina 1 - Installing the 2.0X EPROM

Page 1TRANSPORT®These procedures describe how to upgrade the TxPORT1559 APS Manager from version 1.15 to version 3.XX. Thetest center and central offi

Pagina 2 - Interface Setup

Page 26. Insert the upgrade kit EPROM labeled Rev. 2.0X intothe EPROM socket (U32) being careful not to bend anyEPROM leads. After you install the EPR

Pagina 3 - Uploading the Database File

Page 3space bar) until the display matches the communica-tions port that the PC uses to communicate with the1559 Manager.2. Move the cursor to the Bau

Pagina 4 - Resetting the Unit

Page 41. From the TxPORT Flash Download application on thePC, move the cursor to the Load Configuration fieldand press the Return/Enter key. The mess

Comentarios a estos manuales

Sin comentarios

Verilink 1559 (CG) Configuration/Installation Guide Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Hardware De La Computadora Verilink 1559 (CG) Configuration/Installation Guide. Verilink 1559 (CG) Configuration/Installation Guide User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Verilink 1559 (CG) Configuration/Installation Guide Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Hardware De La Computadora Verilink 1559 (CG) Configuration/Installation Guide. Verilink 1559 (CG) Configuration/Installation Guide User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware De La Computadora Verilink 1559 (CG) Configuration/Installation Guide